Betekenis van:
phase angle

phase angle
Zelfstandig naamwoord
    • a particular point in the time of a cycle; measured from some arbitrary zero and expressed as an angle

    Synoniemen

    Hyperoniemen


    Voorbeeldzinnen

    1. Cam phase shift angle:4.5.
    2. Cam phase shift angle:3.2.5.
    3. Cam phase shift angle:2.5.
    4. Cam phase shift angle:3.4.6.
    5. Variable valve timing system (if applicable and where intake and/or exhaust)3.2.4.3.1. Type: continuous or on/off3.2.4.3.2. Cam phase shift angle:3.2.5. Porting configuration3.2.5.1.
    6. DC stepping motor, with an angle of step of 18 ° or more, a holding torque of 0,5 mNm or more, a coupling bracket the exterior dimensions of which do not exceed 22 × 68 mm, a two phase winding and an output of not more than 5 W
    7. DC stepping motor, with an angle of step of 18 o or more, a holding torque of 0,5 mNm or more, a coupling bracket the exterior dimensions of which do not exceed 22 × 68 mm, a two phase winding and an output of not more than 5 W
    8. Valve timing2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2. Reference clearances and/or setting ranges (1)2.4.3. Variable valve timing system (if applicable and where intake and/or exhaust):2.4.3.1. Type: continuous or on/off2.4.3.2. Cam phase shift angle:2.5. Porting configuration2.5.1.
    9. DC stepping motor, with an angle of step of 1,8o (±0,09o), a holding torque of 0,156 Nm or more, a coupling flange the exterior dimensions of which do not exceed 43 × 43 mm, a chuck of a diameter of 4 mm (±0,1 mm), a two-phase winding and an output not exceeding 5 W
    10. DC stepping motor, with an angle of step of 18o or more, a holding torque of 0,5 mNm or more, a coupling bracket the exterior dimensions of which do not exceed 22 x 68 mm, a two phase winding and an output not exceeding 5 W
    11. DC stepping motor, with an angle of step of 1,8o (± 0,09o), a holding torque of 0,156 Nm or more, a coupling flange the exterior dimensions of which do not exceed 43 × 43 mm, a chuck of a diameter of 4 mm (± 0,1 mm), a two-phase winding and an output not exceeding 5 W
    12. DC stepping motor, with an angle of step of 18 o or more, a holding torque of 0,5 mNm or more, a coupling bracket the exterior dimensions of which do not exceed 22 × 68 mm, a two phase winding and an output not exceeding 5 W
    13. Valve timing2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:2.4.2. Reference clearances and/or setting ranges (1)2.4.3. Variable valve timing system (if applicable and where intake and/or exhaust):2.4.3.1. Type: continuous or on/off2.4.3.2. Cam phase shift angle:2.5. Porting configuration2.5.1. Position, size and number:2.6. Electronic control functionsIf the engine features electronically controlled functions, the information concerning their performance must be provided including:2.6.1. Make:2.6.2. Type:2.6.3. Part Number:2.6.4. Location of engine electronic control unit:2.6.4.1. What does it sense:2.6.4.2. What does it control:SECTION 3 COMPRESSION-IGNITION ENGINE FAMILY3.
    14. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1.
    15. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1. Position, size and number:4.6. Electronic command functionsIf the engine features electronically controlled functions, information concerning their performance must be provided including:4.6.1. Make:4.6.2. Type:4.6.3. Part number:4.6.4. Location of engine electronic control unit:4.6.4.1. What does it sense:4.6.4.2. What does it control: ’;